Products
$12.00
$14.00
A flat kit to put together a 1:12 scale chaise!
My photos show the pieces (including those fab double-thick cabriole legs) but check out Shannon's super cute artwork (plus a tutorial!) in the photo...
A flat kit to put together a 1:12 scale chaise!
My photos show the pieces (including those fab double-thick cabriole legs) but check out Shannon's ...
$24.00
$28.00
I'm kinda in love with this one. A flat kit, laser cut from heavy chipboard for a secretary, including letter slots behind the fold-up desk. Approx. 6-3/4" tall.
This item is in Dollhouse 1:12 Scal...
I'm kinda in love with this one. A flat kit, laser cut from heavy chipboard for a secretary, including letter slots behind the fold-up desk. Approx...
$17.00
$19.00
Aw... a mini version of the lovely 1:12 scale secretary. Note: this is a flat kit, laser cut from medium chipboard for a secretary, including letter slots behind the fold-up desk. Approx. 3-3/8" ta...
Aw... a mini version of the lovely 1:12 scale secretary. Note: this is a flat kit, laser cut from medium chipboard for a secretary, including lette...
$6.00
$7.00
Oh my... a dollhouse-scale version of the two larger sizes of the Chipboard Sleigh. So cute!
Hint: a tiny snip of the Mini Pine Fern would be a good scale for some greenery inside the sleigh (with,...
Oh my... a dollhouse-scale version of the two larger sizes of the Chipboard Sleigh. So cute!
Hint: a tiny snip of the Mini Pine Fern would be a goo...
$17.00
$20.00
Sweet! A tiny kit (laser-cut chipboard). Love the tiny desktop that folds down!
Note: this tiny size does not have chipboard drawers to fit in the cubbies, but this collage sheet has drawers you ca...
Sweet! A tiny kit (laser-cut chipboard). Love the tiny desktop that folds down!
Note: this tiny size does not have chipboard drawers to fit in the ...
$5.00
$6.00
So simple but so useful! A chunky set of bins with handholds cut into both ends.
The tall one is 1-1/2" x 1-1/4" x 3/4" tall; the short one is same measurements but 3/8" tall. Labels on the Honey &...
So simple but so useful! A chunky set of bins with handholds cut into both ends.
The tall one is 1-1/2" x 1-1/4" x 3/4" tall; the short one is same...
$6.00
$7.00
A useful little shelf unit. Includes tiny holes at the bottom for adding Tiny Wooden Drawer Knobs or Pulls but the holes can easily be ignored or papered over if not needed. Note: the knobs fit pre...
A useful little shelf unit. Includes tiny holes at the bottom for adding Tiny Wooden Drawer Knobs or Pulls but the holes can easily be ignored or p...
$5.00
$8.00
This block of drawers (?) has no feet. See photos above (and links below) for ideas for using on the MCM Legs or Console Stand (or stack a few of these up and make an room divider with lots of stor...
This block of drawers (?) has no feet. See photos above (and links below) for ideas for using on the MCM Legs or Console Stand (or stack a few of t...
$55.00
$65.00
What a beauty! A nice large space (10" wide x 9" deep) with double doors for the front and back (I'm just holding one up for size in the first photo, but there are 4).
The roof can lift off to work...
What a beauty! A nice large space (10" wide x 9" deep) with double doors for the front and back (I'm just holding one up for size in the first phot...
$34.00
$52.00
A smaller size version of the Conservatory - 1:12 Scale. This one is 7" wide; not quite reduced enough for 1:24 scale, but sized for using with the 9x9x1 platform (so you'll have an inch of platfor...
A smaller size version of the Conservatory - 1:12 Scale. This one is 7" wide; not quite reduced enough for 1:24 scale, but sized for using with the...
$17.00
$20.00
Such a simple little corner of a room, but you'll find so many uses for it! Laser cut from heavy chipboard, so nice and sturdy (revised since the photo was taken). Add some shelves... maybe some co...
Such a simple little corner of a room, but you'll find so many uses for it! Laser cut from heavy chipboard, so nice and sturdy (revised since the p...
$9.00
$11.00
A sturdy, laser-cut chipboard base for any little shrine you'd like to perch on a 1" tall base (or have a place to hide wiring).
Ships flat, but easy to put together with a bit of glue. Finished si...
A sturdy, laser-cut chipboard base for any little shrine you'd like to perch on a 1" tall base (or have a place to hide wiring).
Ships flat, but ea...